| Specifications |
| Control system | Performance and function highly integrated Current Vector General Purpose Inverter. |
| Drive performance | Induction motor and Synchronous motor. |
| Maximum frequency | Vector control: 0~300Hz; V/F control: 0~3200Hz. |
| Wave-carrier frequency | 0.5kHz~16kHz; Depending on load, can automatically adjust wave-carrier frequency. |
| Input frequency resolution | Digital setting: 0.01Hz; analog setting: maximum frequency×0.025%. |
| Control mode | Open vector control(SVC);
Closed loop vector control(FVC);
V/F control. |
| Starting torque | G type: 0.5Hz/150%(SVC); 0Hz/180%(FVC).
P type: 0.5Hz/100%. |
| Speed range | 1: 100(SVC) 1: 1000(FVC) |
| Speed stability accuracy | ±0.5%(SVC) ±0.02%(FVC) |
| Torque control accuracy | ±5%(FVC) |
| Overload capacity | G type: 150%rated current60s; 180%rated current3s;
P type: 120%rated current60s; 150%rated current3s. |
| Torque boost | Automatic or manual 0.1%~30.0%, |
| V/F curve | Straight-line V/F curve
Multi-point V/F curve
N-power V/F curve (1.2-power, 1.4-power, 1.6-power, 1.8-power, 2 power square) |
| V/F separation | Two types: complete separation; half separation. AVR output. |
| Ramp mode | Straight-line ramp
S-curve ramp Four groups of acceleration/deceleration time with the range of 0.0–6500.0s |
| DC braking | DC braking frequency: 0.00 Hz to maximum frequency
Braking time: 0.0–36.0s
Braking action current value: 0.0%–100.0% |
| JOG control | JOG frequency range: 0.00–50.00 Hz
JOG acceleration/deceleration time: 0.0–6500.0s |
| Easy PLC, multiple speeds | Up to 16 speeds via the simple PLC function or combination of DI terminal states |
| Onboard PID | Process-controlled closed loop control system |
| Auto voltage regulation (AVR) | Keep constant output voltage automatically when grid voltage fluctuates. |
| Overvoltage/ Overcurrent stall control | The current and voltage are limited automatically during the running process so as to avoid frequent tripping due to overvoltage / overcurrent. |
| Fast current limit function | Protect inverter from overcurrent malfunctions. |
| Torque limit and control | It can limit the torque automatically and prevent frequent over current tripping during the running process. Torque control can be implemented in the FVC mode. |
| Power dip ride through | The load feedback energy compensates the voltage reduction so that the Invertercan continue to run for a short time. |
| Timing control | Time range: 0.0–6500.0 minutes |
| Two-motor switchover | Two motors can be switched over via two groups of motor parameters. |
| Fieldbus | Supports RS485, Profibus-DP, CANlink, CANopen (need extention cards) |
| Background software | Change inverter parameter & vitual oscillograph to monitor inverter status. |
| Command source | Operation panel
Control terminals
Serial communication port
You can perform switchover between these sources in various ways |
| Frequency source | 11 frequency sources, such as digital setting, analog voltage setting, analog current setting, pulse setting and serial communication port setting. You can perform switchover between these sources in various ways. |
| Auxiliary frequency source | 11 auxiliary frequency sources. It can implement fine tuning of auxiliary frequency and frequency synthesis. |
| Input terminal | 6 digital input (DI) terminals, DI5 supports up to 100 kHz high-speed pulse input;
3 analog input (AI) terminals, support 0–10 V voltage input or 4–20 mA current input |
| Output terminal | 2 digital output (DO) terminal (FM supports 0–10 kHz square wave signal output)
1 relay output terminal
2 analog output (AO) terminal that support 0–20 mA current output or 0–10 V voltage. |
| LED display | Displays parameters. |
| Key lock | It can lock the keys partially or completely and define the function range of some keys so as to prevent mis-function. |
| Protection function | Motor short-circuit detection at power-on, input/output phase loss protection, overcurrent protection, overvoltage protection, undervoltage protection, overheat protection and overload protection |
| Optional parts | PG card, brake unit, RS485 card, CAN card, Profibus-DP card |
| Location | Indoor, free from direct sunlight, dust, corrosive gas, combustible gas, oil smoke, vapour, drip or salt. |
| Altitude | Lower than 1000m. |
| Ambient temperature | -10°C to +40°C (de-rated if the ambient temperature is between 40°C and 50°C) |
| Humidity | Less than 95%RH, without condensing |
| Vibration | Less than 5.9m/s2 (0.6g). |
| Storage temperature | －20℃~＋60℃. |